How to Read the Data Sheet for the Product Going on Your Floor

The bid names a system you cannot find anywhere online. Here is how to get the actual manufacturer documents for the base coat and the topcoat, which fields on them are worth your time, and what they tell you that a sales conversation will not.

Ask for the technical data sheet and the safety data sheet for the base coat, and again for the topcoat, by those exact names and coat by coat - then check that what the sheets describe matches what your written quote promises. That single request is the most useful thing a homeowner can do with a garage floor coating bid, and almost nobody does it. Vetting the company is a separate exercise and a well-covered one. This is about vetting the material, which is the part that ends up bonded to your slab for the next decade of Kenosha winters.

TL;DR

Request four documents, not one: technical data sheet plus safety data sheet for the base coat, and the same pair for the topcoat. A house-brand or private-label name is normal and not a red flag by itself - no sheet at all is. On the technical sheet, read the surface preparation the manufacturer requires, the application conditions it allows, the recoat relationship between layers, and the limitations section. Then hold all of it against the wording of your contract.

Why the name on your quote returns nothing

You searched the system name from the bid, got a handful of unrelated results, and started wondering what you were being sold. That reaction is reasonable, but the usual explanation is dull rather than sinister. Coating companies very often sell under their own house name, applied to material formulated and manufactured by somebody else. Private labeling works the same way in flooring that it does in the grocery aisle, and it does not tell you anything about quality in either direction.

So a name you cannot find is not the problem. The problem would be a name you cannot find attached to material nobody will document. Every coating that goes on a floor was made by someone, and that someone produced paperwork for it, because installers cannot work without knowing what the product needs. Your job is not to identify the manufacturer. Your job is to confirm the paperwork exists and to read the parts of it that affect your garage.

Two documents doing two different jobs

People use the terms interchangeably and they are not interchangeable at all.

The technical data sheet is the manufacturer describing the product to whoever is going to install it. It covers what the material is, what it can go over, how the surface has to be prepared first, the conditions in which it may be applied, how the layers relate to one another, and what the finished coating is and is not expected to resist. It is written for a contractor, not a buyer, which is exactly why it is useful - nothing in it is trying to sell you anything.

The safety data sheet is the chemical safety document. It covers composition, hazards, handling, storage, first aid and disposal. It follows a fixed section order and always looks broadly the same regardless of the product, because that structure is set by OSHA hazard communication requirements rather than by whoever printed the label. If you have never seen one, the general format is summarized well in this overview of the safety data sheet. For a homeowner the practical value is knowing what will be in the air of a garage attached to your house on install day, and what the crew should be doing about it.

The request, word for word

Send this by email so you have it in writing, and send it before you sign rather than after.

Copy this

"Before I sign, could you send me the technical data sheet and safety data sheet for the base coat you plan to use on my floor, and the technical data sheet and safety data sheet for the topcoat? I would like the sheets for the specific products, not a brochure for the system."

Two things make that request work. The first is asking coat by coat. A flake floor is a layered build - a base coat carrying the flake and a separate topcoat sealing it - and asking about "the system" invites one glossy summary covering neither. The second is naming both document types, because "send me the spec" gets interpreted however the recipient likes.

Note what you are not asking for. You are not asking who manufactures it, which a company may consider commercially theirs and may decline to say. You are asking for the documentation that governs how the product on your floor has to be installed. That is a normal request and no working installer is troubled by it. If you want the rest of the vetting to go with it, our local checklist for vetting a coating contractor covers insurance, prep and warranty questions.

Ask us for the sheets before you ask anyone else.

Base coat and topcoat, both documents, sent over so you can compare bids properly. The on-site quote is free.

What to read once the sheets arrive

A technical data sheet is a dense page or two and most of it is aimed at an applicator. These are the parts worth a homeowner's attention, and what each one is actually telling you. The values will be whatever that manufacturer states for that product - nothing here is a universal figure and you should be suspicious of anyone who quotes you one as if it were.

Field on the sheetWhat it is telling you
Product name and identifierWhether this sheet is genuinely for the product named on your quote, or a relative of it
Description and generic typeThe chemistry family in plain terms, which is what lets you compare two bids that use different marketing words for the same thing
Surface preparationWhat the manufacturer requires the concrete to be brought to before their product goes on. If a bid proposes less prep than the sheet demands, that is a real conflict
Application conditionsThe slab and air conditions the product may be installed in. This one matters here: an unheated garage in a Kenosha November is a genuine question, not a formality
Coats and recoat windowHow many coats the manufacturer expects and the timing relationship between them - a direct check on a schedule you were quoted
Cure and return to serviceThe manufacturer position on when the floor can take foot traffic and vehicles, which is the honest source for that answer
Resistance dataWhat the cured coating is stated to handle. Road salt, hot tires and UV are the ones that matter to a garage in this county
Limitations and exclusionsRead this section twice. It is where a manufacturer says plainly what their product is not for, and it is the single most informative paragraph on the sheet

The comparison that matters most

Having the sheets is not the point. The comparison is the point, and it goes three ways.

Sheet against contract. If the technical data sheet requires the concrete to be mechanically profiled and the quote describes a cleaning and an etch, those two documents disagree, and the one you signed is not the one that governs whether the coating stays down. If the sheet describes a two-coat build and the bid describes one, ask which is happening. Any gap between the two is a question, not necessarily a problem, but it must be a question you ask before the work rather than after.

Sheet against your garage. Application conditions are where this gets local. A Kenosha garage in late autumn is not a conditioned warehouse, and the difference between products shows up exactly there. Ask what the plan is if the slab is colder than the sheet allows on the day. A good answer exists. A shrug does not. Our piece on coating a floor through a Wisconsin winter covers why slab temperature rather than the calendar is the deciding factor.

Sheet against sheet. Once you have documents from two bidders you can compare like for like instead of comparing adjectives. Two salespeople can both say "commercial grade" and mean entirely different chemistry. Two data sheets cannot. If you want the background on what each layer in a flake floor is doing before you sit down with the sheets, the polyaspartic garage floor page covers the topcoat and the epoxy garage floor page covers the base, both in plain language.

When nothing turns up

Sometimes the request just goes quiet, and that is information too. A company that installs coatings every week has these documents in a folder on a phone, because the prep requirements and application conditions are things they work from. Producing them is not research.

So treat a long silence, a brochure sent instead of a sheet, or an explanation of why the sheets cannot be shared as part of your answer about that bidder. It costs you nothing to have asked, it happens before any money moves, and it is the cheapest filter available to you. Ask us the same question and see what comes back - book a free on-site quote, and the sheets for both coats come with the written scope so you can lay them next to anybody else's. What we install and why is on the garage floor coating page.

Get the paperwork with the quote.

Written scope, both coats documented, nothing to chase afterwards. We reply the same day.

Data sheet questions

I searched the system name on my quote and got nothing. Is that a bad sign?

Usually not. A great many coating companies sell under a house name applied to material made by an established manufacturer, so the name on your bid may exist nowhere except that company. What turns it from normal into a problem is if nobody will send you a data sheet for it. A product with no findable name and no sheet behind it is the combination to worry about, not the name on its own.

What exactly should I ask a contractor to send me?

Two documents for each layer, named plainly: the technical data sheet and the safety data sheet for the base coat, and the technical data sheet and safety data sheet for the topcoat. Asking for the sheets for the system as a whole is how you end up with one brochure. Asking coat by coat is how you find out what will actually be applied.

Technical data sheet or safety data sheet - what is the difference?

The technical data sheet is the manufacturer describing how the product performs and how it must be installed - what it goes over, the conditions it can be applied in, how the coats relate to each other, what it resists. The safety data sheet covers what is in it and how to handle it safely. They answer different questions and you want both.

Is a private-label coating worse than a name-brand one?

Not inherently, and it is worth being clear about that. Private labeling is ordinary practice across a lot of industries, and plenty of house-branded coatings are perfectly good material made by a major manufacturer to a known formulation. The test is not whose sticker is on the pail. The test is whether a real data sheet exists for it and whether that sheet matches what your contract promises.

What should I actually do with the sheets once I have them?

Read three parts: what the manufacturer says the surface has to be prepared to, the conditions the product may be applied in, and the limitations section near the end. Then hold those against your written quote and against your own garage. Most of the questions worth asking a contractor come straight out of that comparison.

What if the contractor will not send them?

Treat that as the answer. Nobody who installs these products for a living has trouble laying hands on the sheets, because they need them to work from. A refusal, a long delay, or a marketing brochure sent in place of a sheet all tell you something useful, and none of it costs you anything to find out before you sign.

Free On-Site Quote

Get your free, on-site quote.

Tell us about your floor and we'll call you back the same day to set up a free measure and price.

Get your free quote

Tell us about your floor and we will call you back the same day. No obligation.

What are we coating?

Licensed & insured · Free, no-pressure quotes · Serving Kenosha County, WI

By submitting, you agree to our Privacy Policy and Terms, and consent to be contacted by phone, text, or email about your project, including by automated means. Consent isn't a condition of purchase. Msg & data rates may apply.

Call us - get a free quote